Watt ANKA (ASC34) 3/4 højtryks poly-rør lige koblingsindsats, fitting

Name: Watt ANKA (ASC34) 3/4 højtryks poly-rør lige koblingsindsats, fitting
Brand: Watts
SKU: 0098268149913
Price: 205.42 DKK
Availability: InStock

Brand:Watts

3.6/5

kr
205.42

Giver lækagefri* beskyttelse og er UV-stabiliseret til applikationer over jorden eller under jorden. Højkvalitets glasfiberforstærket nylonkonstruktion giver korrosionsbestandighed og langvarig, genanvendelig slid. Hurtig og nem at installere; Tilslutning kan foretages i hånden, uden at der kræves specialværktøj. Forbinder effektivt polyethylenrør, -rør og -slange. Ideel til landbrug, kunstvanding, landlige og kommunale og VVS-applikationer.

Beløb

Tilføj til kurv Køb nu

EAN: 0098268149913

Kategorier Industri og videnskab, Hydraulics, Pneumatics & Plumbing, Tubes, Pipes & Hoses, Pipes,

Brand	Watts
Color	Fitting
Connector Type	Barb
Exterior Finish	Stainless steel
Item Dimensions LxWxH	1.95 x 6.4 x 1.45 inches
Material	Polyethylene, Nylon
Size	3/4 inch

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med^*

Din vurdering

Scritto da: Scott Sullivan

Worth its weight in gold

I recently laid a pex type plastic 3/4” pipe to my shop and had to tie the plastic piping into pvc for my faucet and this was a life saver, the design makes this thing bulletproof as far as leaking I will most definitely be ordering more to keep on hand. A lot cheaper than pex fittings and just as reliable if not more.

Scritto da: Anonymous

It works

Really easy to apply

Scritto da: Jeff

Worked perfectly for me

The media could not be loaded. Landscapers cut the 3/4” rainbird irrigation pipe with shovel causing a leak. Cut the broken section out, bought a new section of pipe at Lowe’s and used this gizmo to connect the ends securely with no leakage.

Scritto da: Mac Ling Candy SC

Easy to insert into the tubing and the Hand tightening nut

The fittings were easy to press all the way into the Tubing and tightening the nut on the thick PP tubing. I was surprised that they were so easy to assemble and the fittings had No leaks even after 1 month of constant 50 PSI pressure on the the tubing.

Scritto da: Victor

Can't trust it.

I used it on a commercial 3/4 hose from home depot. When you tighten it down it tends to push the hose off instead of riding up and over it. So it only catches on the end of the hose. Can not trust leaving the water turned on.. I would think that on a thicker hose it would not work at all. If it can only be used on a cheap thin hose then why bother repairing it just buy a new hose.

Scritto da: wongton

push hose further

i bought this to repair a poly pipe, one reviewer says the hose tends to slip off the coupling end, another says wrap some duct tape to the end to prevent slipping, I think the hose slips because the hose is not pushed in far enough..... my photo shows when the blue nut butts against the raised tab, my hose is pushed almost next to it, this way it rides over the coupling about an inch, I used a hair dryer to soften the hose and it was very easy to push it in, or use some warmer water.....i tightened the right side nut and then unscrewed it just to check, the hose did not move, I re-tightened and the connection is leak free I initially bought a poly coupling and some hose clamps from Ace Hardware, while I think that would work also, this ANKA product is stronger, the middle part is thicker than the small Ace coupling. the nut feels stronger than regular plastic, once the nuts are tightened the connection is very secure