Dremel 420 afskæringsskive, 15/16 (23,8 mm) diameter, 0,40" (1,0 mm) skivetykkelse, tilbehør til skærende roterende værktøj (20 stykker), sølv

Brand:Dremel

3.7/5

kr
177.54

PRODUKTBESKRIVELSE Få mest muligt ud af dine Dremel roterende værktøjer ved at bruge vores innovative og omfattende udvalg af roterende tilbehør og tilbehør. Uanset dit projekt, har vi den perfekte løsning til dig. Dremel-tilbehør passer ind i dit roterende værktøj for at udvide dets alsidighed. Uanset om du ønsker at udskære, gravere, skære, slibe eller slibe, er der et Dremel-tilbehør til at få arbejdet gjort med præcision. Derfor lader vores specialbyggede Dremel-tilbehør dig få dit projekt helt ned til mindste detalje. Dremel-tilbehør er også farvekodet i brugskategorier for at gøre det nemmere for dig at vælge det rigtige tilbehør til dit projekt. Gør dit Dremel roterende værktøj til en skæremaskine med 420 Dremel afskæringsskiver. God til at skære i skiver, lave lige snit og slidser i alle slags metal, såsom hærdet stål, metalplader eller aluminium. Skærehjulene har en 15/16 tommer. (23,8 mm) hjuldiameter og 0,04 tommer. (1,0 mm) tyk klinge gør den ideel til at skære, rille og trimme en række forskellige metaller, tyndt træ eller plast; kan også bruges til at lave slidser i rustne eller afisolerede bolte og skruer. Kun til brug med 402-dornen. Pakke med 20 hjul. Kompatibel med alle Dremel ledninger og akku roterende værktøjer. Der er ingen grund til at jage efter den rigtige spændetang, alt Dremel roterende tilbehør har et 1/8" standardskaft. AMAZON.COM Dremels 15/16-tommer kraftige skæreskive er ideel til at skære, rille og trimme alle slags metal. Det kan også bruges på andre materialer, herunder tyndt træ, plast og keramik. Denne skæreskive er konstrueret af et hårdt slibemiddel, der bruges til at skære og skære metal, inklusive hærdet stål. Dette hjul gør det nemt at skære bolte og skruer, og lave slidser i rustne eller afisolerede bolte og skruer til afmontering med en skruetrækker. Dette 1/2-tommer tykke polerhjul kommer i en pakke med 20 stk.

Ingen tilgængelige enheder

EAN: 640026953777

Kategorier Værktøj og boligforbedring, Værktøj & Håndværktøj, Elektroværktøjsdele og tilbehør, Elektrisk roterende værktøj dele & tilbehør, Cutting Wheels,

Til brug med roterende værktøjer, der kan rumme en 1/8 skaftstørrelse. Skærehjulet skærer kun langs kanten. Forsøg ikke at slibe eller skære buede huller med dem. Ideel til at skære slidsbolte, skruer, metalplader og tyndt træ. Gør dit roterende værktøj til en skæremaskine.

Assembled Diameter	23.8 Millimeters
Assembled Diameter	‎23.8 Millimeters
Batteries Included?	‎No
Batteries Required?	‎No
Brand	Dremel
Color	‎Silver
Construction Type	Cut-off Wheels
Country of Origin	‎China
Customer Reviews	4.6 4.6 out of 5 stars 1,212 ratings 4.6 out of 5 stars
Cutting Diameter	‎23.8 Millimeters
Grit Number	180
Grit Rating	‎180
Is Discontinued By Manufacturer	‎No
Item model number	‎420
Item Package Quantity	‎20
Item Weight	‎0.192 ounces
Manufacturer	‎Dremel
Material	‎hard abrasive material
National Stock Number	‎3460-01-275-4363
Part Number	‎420
Product Dimensions	0.94"L x 0.94"W
Warranty Description	‎No

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med^*

Din vurdering

Scritto da: Donald Scheer

Most Used Dremel Item I Use!

I Use These Often! So I Need A Lot Of Them! They Do A Great Job! Like All Cut-off Wheels They Wear Out Or Break! But, They Arer A Great Prodsuct.

Scritto da: Brian K Johnson

Cut of discs

These cut off discs work fine but they are not strong, they break fairly easily, but they are very inexpensive so they are still useful.

Scritto da: Rich

Did what it supposed to do.

Durable and holds to cut metal. Better than snapped on Dremel wheel. Highly recommended.

Scritto da: Whale

When you are tired of breaking cuttoff wheels, get this

Cut off tools are for cutting shafts that are usually hard steel and not so thick. But when the going gets rough and you need to cut aluminum pieces that are soft and explode your nice think blades, this is the one you need. It will deal with a lot more lateral side loads and can remove material besides just cut a slot. If I need a cut in a hardened piece of steel, the then thin cutoff tools work. But if i need to cut out a piece from an aluminum sheet or maybe remove some excess aluminum weld material, the thicker cut off wheel will last much longer although they may still explode if you force the issue. I use both cutoff tools and use the one that will survive. Usually the thicker one.

Scritto da: Nana and Pa

Excellent product

Working very well on hard steel material. Very pleased with quality of the wheels.

Scritto da: @4x4Erik

Awesome blades

These are an absolute a must have for me. I always have a supply of them. I will say, these seem to be a more coarse grit than the wheels I've had in the past, but that can also be a good thing. They last as good as any, and have worked for me.

Scritto da: David

Cut well

They work well but they are fragile. That’s why I bought so many.

Scritto da: Morse Wheeler

Dremel quality is just better than everything else

I've tried several other brands of less expensive cut-off wheels, but they have all been garbage and most lasted no more than a couple of seconds before disintegrating. Dremel wheels are just so much better...end of story. They are much thicker than the knock-offs, and unless you bind them in the workpiece, almost always wear all the way down as they should. The Dremel wheels are definitely in the category of "you get what you pay for".

Scritto da: J Le G

Great for my purposes.

Excellent for small jobs on the appropriate materials.

Scritto da: Amazon Customer

Exactly as described

I use these during my radio controlled aircraft building.

Scritto da: Steve Randall

Five Stars

Arrived safe

Scritto da: Frédéric J.

Very good "all-around" Cutting Wheel

Actually they're similar to those which came with my Dremel kit (I had only two, so I needed a refill of those "all-around" wheels). And I luv'em! I'm currently moding PC chassis, and they are perfect for : 1- Cutting through plastic, like butter. For instance I used it on an NZXT RGB LED Controler 5.25" plastic enclosure, as well as a SlimODD + 2x2.5"SSD/SSHD 5.25" bay adapter, cutting holes and redesigning edges on the sides so that I could run SATA, USB and Power wires "through" the bay controllers cage, leaving room for a Swiftech 280mm radiator plus its pump on the front lower side of the radiator (thus very tight to the bay cage). Their diameter is not too big, enough for that scale of craftsmanship. 2- Cutting curves on metal sheets. I'm using it while moding a Fractal Refine R4 PC chassis, for accommodating a 280mm CPU water cooler's radiator on the top panel ("opening" 27mm towards the left side panel: new "air vents" and mounting holes for 2x140mm fans - this mod clears the obstruction the motherboard's Power regulators Heat sinks had with the original chassis mounting holes vertical alignments - and which disallowed any 280mm radiators on the top panel). One of their "con", is also a "pro": they degrade relatively fast. I can thus use them for cutting curves, i.e. for rounding corners on steel (or aluminum) sheets, or for cutting out patterns/works of arts, their smaller radius giving more flexibility on curved lines. For straight lines or large arcs I prefer the Dremel 426 Fiberglass Reinforced, which have a bigger radius (1 1/4") for straighter cuts. I'd like to find 1 1/2 inch though, as I don't know if going with a "non-standard" proprietary mounting system like the EZ Lock (for which there's an offer of 1 1/2" cut-off Wheels), is really worth the investment...

Scritto da: Ray A

Not as heavy duty as one might expect.

Even though these disks are sold as heavy duty, take it with a grain of salt. Unless you are very careful when cutting material the disks will break and pieces of shrapnel will fly, so make sure you wear protective glasses to save your eyes!.