TotalBoat Flotation Foam - 2-delt ekspanderende polyurethan Marine Pour Foam til bådflydning, isolering og lydisolering (2 LB densitet, 2 gallon sæt)

Brand:TotalBoat

3.6/5

kr
1971.18

Bliv sikrere og mere komfortabel på din båd med Total Boat Two Part Polyurethane Marine Expanding Foam. Dette US Coast Guard-kompatible hældeskum bruges almindeligvis til at tilføje opdrift for at holde en båd flydende, hvis skrogets integritet kompromitteres. Dens lukkede celleskumstruktur gør den i stand til at modstå vandabsorption i mange år, hvilket gør den ideel til at fylde pontoner og hulrum i kajakker og under båddæk. 2 Lb. densitetsekspanderende urethanskumsæt blandes for at danne et hurtigthærdende, hældbart flydende skum, der hærder til et stift, letvægtsmateriale, der også er fantastisk til at udfylde huller, lydisolering og give termisk skumisolering og ikke-strukturel støtte i en række marine, husholdnings- og kunst applikationer.Todelt flydeskum har et enkelt blandingsforhold på 1:1, der gør det nemt at bruge. Varme forhold på 75-85°F er meget vigtige, ligesom nøjagtig måling, grundig blanding og korrekt udluftning af det område, hvor skummet skal påføres, fordi det udvider sig enormt i volumen. Bland blot en del harpiks og en del aktivator, omrør kraftigt i ca. 25 sekunder for at blande fuldstændigt og hæld straks i det forberedte område. Ekspanderende skum vil fordele sig jævnt - selv i uregelmæssigt formede områder. Hærdet skum hærder i form med minimal krympning og kan nemt skæres til. Når de er fuldstændig hærdede, skal områder, der udsættes for sollys, lamineres eller overmales med polyester-, epoxy- eller vinylesterbelægninger. For at få de bedste resultater ved at fylde større områder, hæld i flere lag for at tillade korrekt hærdning og maksimal styrkebinding mellem lagene. Bær altid ordentlig øjen-, ansigts- og tøjbeskyttelse, når du blander og hælder todelt marineskum. Sammenlign med Evercoat Marine Foam-It, FGCI Polyurethane Foam, Polymer Planet Liquid Urethane Foam, Morris Materials Urethane Pour Foam, True Composites Pour Foam og System Three Flotation Foam til både. Alle TotalBoat-produkter giver stor værdi og fantastiske resultater. 100% lavet i USA.

TILGÆNGELIG I ET 2 QUART SÆT OG ET 2 GALLON SÆT; Udbytte: 2 Quart Kit – 2 kubikfod; 2 gallon sæt – 8 kubikfod; Flotation Range for 2 lb skum: 75 lbs pr. blandet 2 quart sæt og 300 lbs pr. blandet 2 gallon sæt; holdbarheden er 6 måneder fra fremstillingsdatoen. DEN IDEALE ARBEJDSTEMPERATUR ER 75-85°F; korrekt temperatur, timing, blanding og udluftning er afgørende for korrekt skumekspansion; under 75°F falder ekspansionen; efter blanding udvider skummet sig hurtigt og bliver stift, så rengør overfladen på forhånd og vær klar til at hælde. 94% LUKKET CELLE SKUM: Perfekt til marine applikationer; modstår vandabsorption og skader fra gas, olie eller opløsningsmidler; når det er hærdet, kan skum belægges med polyester, epoxy eller vinylesterharpiks; kan også nemt skæres eller skæres i form. LET AT BRUGE: Flydende urethanskum har et enkelt blandingsforhold på 1:1, udvider sig hurtigt og hærder på plads på cirka 5 minutter. ved 70-80°F; for at bygge flere lag til påfyldning under båddæk, hæld ekspanderende skum i separate partier. LETT, TODELT POLYURETHANSKUM: Ideel til at tilføje opdrift, termisk isolering, lydisolering og udfylde huller eller hulrum; kun til ikke-strukturelle anvendelser; testet i overensstemmelse med U.S. Coast Guard Regulation # 33 CFR 183.114.
Brand TotalBoat
Color Clear
Compatible Material Vinyl
Is Discontinued By Manufacturer No
Item Form Liquid
Item model number TB-FOAM
Manufacturer TotalBoat
Material Polyurethane Resin
Product Dimensions 8.5 x 6.5 x 10 inches; 20 Pounds

3.6

9 Review
5 Star
81
4 Star
9
3 Star
4
2 Star
2
1 Star
4

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med*

Scritto da: bugalou
Some hints for people using this.
So I have used a ton of this for a few projects. This will hopefully help some of you guys. 1: buy a couple just jugs of acetone. It really helps cleanup the sticky goo you will have to deal with. 2. Invest in the cheap plastic mixing cups with the proportion lines. If you are doing semi enclosed areas don't poor to much in so the foam can full expand and you do not waste product. 3. Buy one of those cheap rechargable milk froather mixers they have for coffee. It makes mixing things way easier and more consistent. It will likely be ruined after, but they are only like 12 bucks. 4. Buy some small silicone scrapers like what you use for the kitchen. If you let them sit in acetone in a cup, you can use it to scrape the left overs from your mix cups after you pour and save some mess. You can usually get several Uses out of each cup doing this and reduce the mess. 5. Nitrile gloves are must. This stuff gets every where.. You can use Acetone to clean up. 6. Probably the most important part - chill the two parts in the refrigerator overnight. This slows the reaction and gives you time to actually mix it throuroughly and pour it without having to rush around. Once it warms. It will behave normally and start expanding. Lastly if you spill it on accident, left it dry completely before cleaning up. It's much easier to dea with dry. I'm working on an idea to hook this to a gun the auto mixes components and despenses it in a more controlled manner. If I have any success I will post and update.
Scritto da: Curtis Hall
Trial and Error, Read the directions first. I did and still has a learning curve.
Applying concoction into sit on top kayak Started out not liking it much. It's early November in Central Texas and the outside temperature was around 80 degrees, the sun was out and warm. The cans were stored in my shed, and the temperature of the resin and activator were probably around 50 degrees. I mixed up a little bit of this stuff into a wash basin and put it in my kayak. The stuff didn't really foam up. Realization: Just because the outside temperature is 80 degrees still does not mean that the foam will work. I found a pot large enough to put one can in at a time (wife was watching TV at the time :). Light up the stove top and bring the temperature of the resin and activator to around 80 degrees (shake in a circular motion to mix hot and cold, I had to put on the stove 3 times per can). I used my hands to measure the temperature. Nothing scientific. I screwed off the top of the foam can and had to poor it quick... It was trying to foam up. I used a wash basin to mix the 2 together. Don gloves, this stuff adheres to everything and is difficult to remove. Ensure that the hole that you are putting this stuff into is fairly large (Mine is almost the size of my head and still got this stuff all over my kayak.) It worked ok at first, but after the first batch started to heat up the inside of my kayak the rest of the stuff worked like a charm. It filled up the whole back end of my 2 person kayak. After it's done foaming it turns hard. I can still scrape it with my fingernail. But, for filling the void and stabilizing the outside hull, it did a superb job. I just bought a second batch to fill up the front end of my boat. I hope this helps.... happy foaming :) Second purchase I didn't have to heat up since I left it out in the sun. Kayak was in the sun as well and this stuff worked great. I mixed up a little at a time, and then pour it in. This time after the pouring in 2-3 batches I took the kayak off the shed it was leaned up against and turned it topside down to spread the foam all over. It still worked great but got some on my hands this time... they turned black. I rubbed them against a brick wall and the blackness deteriorated. Not completely gone but it's not as prevalent.
Scritto da: Satisfied
Easy to use if following directions
Easy to use if you follow directions. Must mix fast and pour quickly.
Scritto da: Sean hayes
Saved my skiff!
I am so happy that I decided to go with this product because it literally saved me from having to buy myself another boat. I'm sure you all have heard of Carolina skiff's notorious problem with water in the haul and unfortunately that's exactly what happened to me. Took some of the floor up ripped up the waterlogged foam let the boat drive for about 48 hours and then I poured my foam. Make sure you mix it really good and you're absolutely 100% ready for the poor as it does rise extremely fast. The instructions were 100% accurate as it does take about 7 minutes to fully cure, and when it does it becomes extremely hard. If you do make a mess in your boat with the phone don't worry because it scrapes off with ease.
Scritto da: James Holaday Jr
The foam worked better than I had imagined
I used this foam in my 1974 Meyers Aluminum boat while I was replacing the floor. The foam worked better than I had imagined. It filled every nook and cranny and once I got the floor in it doesn't make a sound. Tips; Get the room your working in as hot as possible or if outside wait for a hot day. The hotter the area the more the foam rises and the more area you can fill per pour. Warning, try to measure the portions as close as you can because once this stuff gets going you will not be able to stop it and you will have a lot of waste from overflow. (I wasted about a quart in overflow) Make sure the foam has plenty of room to grow and has an escape for overflow. It bowed a metal plate I had riveted in the floor because it couldn't get out and I had to drill a hole quickly to give it room. Also this stuff is extremely sticky so clean your measuring cups and tools after each pour. Also purchase a drill mixer, you will not have enough time to properly mix the two parts by hand before it starts rising, which happens about 35 seconds after mixing starts. I have to say this is the most fun I have ever had during a project. I felt like a kid in science class watching the two chemicals mix and then start growing. I would recommend this product to anyone who is looking to fill space under a boat floor.
Scritto da: Anthony G.
Garbage
Product is supposed to be a 94% closed cell flotation foam product. Followed installation instructions and watched several videos and now have unusable Swiss cheese in my boat that will cost a fortune to remove!!!!
Scritto da: Christine Lafleur
Super
Donne les resultats escomptés. Je recommande.
Scritto da: Carol Hall
Easy application
Worked great , wish I had ordered more ????
Scritto da: Brandi
Product was amazing
Used this product for filling my boat and was very interesting watching it expand

Relaterede produkter

hot
Ronstan Splejsesæt
4.1/5

kr 2378.87

Ronstan Splejsesæt
4.1/5

kr 2378.87

hot
STAR BRITE vandskraber (040042)
3.1/5

kr 495.29

STAR BRITE vandskraber (040042)
3.1/5

kr 495.29

hot
FIFTY-FIFTY Kirsebærrød
3.7/5

kr 286.06

FIFTY-FIFTY Kirsebærrød
3.7/5

kr 286.06

hot

Oplev vores internationale netværk

Vi sender til 28 lande, over 200.000 produkter. Hold dig opdateret, tilmeld dig nyhedsbrevet.

Array