The Hillman Group 59660 5/8 x 7/8 x 1-1/2-tommer sømløst stålafstandsstykke, zinkfinish, 5-pak

Brand:The Hillman Group

3.4/5

kr
281.93

Varer sælges enkeltvis i detailhandlen. Disse runde træknapper måler 1 i diameter. Sømløse afstandsstykker i stål er nemme at installere og har større holdekraft end andre afstandsstykker. Dele, der er ideelle til at yde støtte og justering til printkortsamlinger, paneler og døre. Stålafstandsstykker bruges til at skabe plads mellem to genstande for at placere dem korrekt.

Varer sælges enkeltvis i detailhandlen. Disse runde træknapper måler 1 i diameter. Sømløse afstandsstykker i stål er nemme at installere og har større holdekraft end andre afstandsstykker. Dele, der er ideelle til at yde støtte og justering til printkortsamlinger, paneler og døre. Stålafstandsstykker bruges til at skabe plads mellem to genstande for at placere dem korrekt.
Exterior Finish Zinc
Head Style Round
Manufacturer Grade Grade 2
Material Steel
Thread Size Round

3.4

8 Review
5 Star
77
4 Star
6
3 Star
6
2 Star
0
1 Star
11

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med*

Scritto da: Richard R. Graham
dimensions are correct
The inner diameter is correct. Had to clean rust, corrosion, etc off surface of old axle and the spacer went on easily.
Scritto da: frenchiefellow
Fits 5/8" threaded bolt
I purchased a few 10" long, 5/8" diameter threaded hex bolts for a project I was working on. Originally needed 8.5-9" bolts at a minimum, but only 10" length could be found. Thus I needed spacers (I have no tools to cut the bolt) so I could have a snug connection and a mechanism to easily remove the nuts by hand at any time. Happy to report these easily fit on the threaded end and the un-threaded part and satisfy my needs. Only needed 2 but 5-pack was more economical.
Scritto da: Mlkcrawford
Too Tight
So, got these as axle spacers for a tow behind trailer. They will not slide onto the axle, or force on with heat or cold. Bottom line is, they are about 1/32 of an inch tighter than advertised . . . so . . . don't expect this 5/8 to fit a 5/8 axle, and with the available sized, you have to drop down considerably to get one that fits right. Not giving it a "bad" rating, since they are well priced and quality items, just misleading sizing
Scritto da: CityZero
Fit fine on a 5/8 dump cart axle.
Bought some 10" tires for a lawn cart we got a super deal on but it had bad tires. Hubs weren't wide enough and there was too much play. These spacers fit on the axle after a light sanding of the rust. I did have to cut them off a little bit with a reciprocating saw to get the width just right. They work great.
Scritto da: John
Solid construction. Works as expected on wheelbarrow axel.
Solid construction. Works as expected. Used on wheelbarrow axel to offset wheel on each side.
Scritto da: Anthony
Off Center and oversize
If you are using these on rotating components, look elsewhere. Luckily I am using these as shims on a static part. I was able to sand them down to 7/8, but the holes are 5-1000 off center which would cause vibration on rotating parts.
Scritto da: Richard
I'm sure it is a good product, but I can't rate it, package was empty when received
I liked what I ordered and will rate it when I receive them. Thank you Richard Chapman
Scritto da: Amazon Customer
Three Stars
E

Relaterede produkter

Oplev vores internationale netværk

Vi sender til 28 lande, over 200.000 produkter. Hold dig opdateret, tilmeld dig nyhedsbrevet.

Array