Svært at finde fastener 014973239640 Elevatorbolte, 1/4-20 x 2, stykke-10 1/4-20 x 2

Brand:Hard-to-Find Fastener

3.8/5

kr
218.20

Vi har et bredt udvalg af fastgørelseselementer, der er ideelle til mange anvendelser i hjemmet, gården, forretningen, bilindustrien og i industrien. De fleste af vores fastgørelseselementer har en let zinkbelægning over stål, hvilket giver en mere rustbestandig overflade. Vi sælger også coatede og rustfrie produkter for yderligere rustbestandighed. Vi lagerfører mange kvaliteter af fastgørelseselementer lige fra stål med lavt kulstofindhold til hærdet, varmebehandlet stål. Ikke alle fastgørelsesanordninger er anvendelige til alle applikationer, så sørg for at teste grundigt og få udtalelsen fra en autoriseret bygning eller certificeret bygnings- eller konstruktionsingeniør, før du stoler på disse fastgørelsesanordninger i situationer, hvor fejl ville resultere i skade på ejendom eller person.

Hovedstil: Flad forsænket. Finish: Zink. Materiale: Stål. Længde: 2 tommer. Diameter: 1/4.
Assembled Diameter ‎0.25 Inches
Batteries Included? ‎No
Batteries Required? ‎No
Brand ‎Hard-to-Find Fastener
Country of Origin ‎China
Customer Reviews 4.7 4.7 out of 5 stars 316 ratings 4.7 out of 5 stars
Cutting Diameter ‎0.25 Inches
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Zinc
Exterior Finish ‎Zinc
Fastener Type ‎Elevator Bolt
Finish ‎Zinc
Grade Rating Grade 5
Grade Rating ‎Grade 5
Head Style ‎Dome
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Item model number ‎014973239640
Item Package Quantity ‎1
Item Weight ‎1.76 ounces
Manufacturer ‎Hard-to-Find Fastener
Manufacturer Grade Grade 2
Manufacturer Grade ‎Grade 2
Material Steel
Material ‎Steel
Measurement System ‎Inch
Part Number ‎EBFCS-070-10
Product Dimensions ‎3.5 x 2.62 x 1.44 inches
Size ‎1/4"-20 x 2"
Thread Size 1/4"-20
Thread Size ‎1/4"-20
Thread Type ‎Coarse

3.8

8 Review
5 Star
80
4 Star
15
3 Star
2
2 Star
1
1 Star
1

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med*

Scritto da: Blake Sullivan
You can get creative w these. Note: countersink.
These things are great. Needed to find something rock solid for mounting a boxing speed bag platform through 3/4” maple planks while sitting flush against OSB prior to bolting the entire unit through studs w lags. These are so much better (and easier) than carriage bolts if you’re looking to make that perpendicular connection which needs a flush backing. NOTE: keep in mind there’s a very slightly angled flange on the underside, so you’ll need to sand a small area (I did a very non-pro/DIY-worthy job of this w Dremel+sanding cones and it still worked great) countersink and note the square; and make sure to account for the small, square shaped pieces which connects the bolt w the head and countersink for that. THESE ARE GLORIOUS WHEN YOU NEED EM!
Scritto da: Luckster
Head is too big
Bolts are of great quality. However, heads are much too large for my use. Listing didnt state diameter, which would have helped in making the correct purchasing decision.
Scritto da: Mustang Gregg
Good hdwe.
I like them.
Scritto da: David Deupree
Worked well!
5 star if they supplied dimensions.
Scritto da: Zach P.
Stripped 3 of 10....bad threads or bad grade?
Had a couple of these 1/4" elevator bolts strip with very little torque. Using these bolts to secure a 3/4" plywood board to mounting brackets on the back of the boat for a swim deck (20"x78"..so not a full sheet) I'm building...wanted the flush surface given a mat is going to lay on top of the deck... Snugging up the first bolt, stripped...swap it out....stripped....third times the charm? Nope.....stripped... Not like I was using a torque wrench to put the nuts on but I can't imagine it was more than 40ft/lbs when these stripped. Super unfortunate cause I can't seem to find any stainless elevator bolts....hopefully the remainder of the ones I used will hold up through stress and use on and around water.
Scritto da: Nico
Disappointed.
Great elevator bolt but the head was too large. It would not fit on a hasp. Still looking for a flat head bolt but with smaller diameter and a half inch longer.
Scritto da: Flip
Good quality
My elevator is firmly held in place, thanks to these fine bolts.
Scritto da: Sam
Hard to find fasteners
These low profile head bolts were exactly what was needed for installing the new bumper, brackets and guard on my truck

Relaterede produkter

Oplev vores internationale netværk

Vi sender til 28 lande, over 200.000 produkter. Hold dig opdateret, tilmeld dig nyhedsbrevet.

Array