POWERTEC 70259 Dust Collection Fittings Network

Brand:POWERTEC

3.4/5

kr
2390.80

Introduktion til Dust Collection Fittings Network fra POWERTEC. Dette sæt indeholder alt, hvad du behøver for at udvide dit netværk af støvopsamlingsslanger, og det er ideelt til rengøring efter stationær træbearbejdning og elværktøj. Uanset om du er professionel eller gør-det-selv'er, tilbyder dette ensemble af støvopsamlertilbehør den perfekte løsning til at udvikle et effektivt og bekvemt støvudsugningssystem til ethvert hjem eller professionel butik med begrænset plads. Disse støvopsamlingsfittings er fremstillet af førsteklasses ABS-plast og giver et klart overblik over blokeringer og er designet til højeffektiv brug. Den er kompatibel med de fleste centraliserede vakuumsystemer og butiksstøvsugere. Støvopsamlingsrør/rør - leverer i alt 24 fod gennemsigtig netværksudvidelseskapacitet. Reducer Fitting – tilsluttes direkte til din butiks vakuumslange, hvilket øger lufthastigheden nær maskinen. Blast Gates (2-1/2”) - designet til at dirigere korrekt luftstrøm mellem støvopsamlerværktøjer og maskiner. (45° & 90°) Støvopsamlings-albuer - hjælper med svært tilgængelige områder, samtidig med at de letter retningsændringer i dit slangenet. "Y"-fitting-konnektorer - perfekt til at muliggøre dobbeltgrenkapacitet. Koblinger – giver en sikker og pålidelig forbindelse til dine komponenter. Monteringsbeslag og hardware – giver mulighed for en hurtig og nem installation (producentens instruktioner medfølger). POWERTEC er en amerikansk baseret producent af træbearbejdningsmaskiner af høj kvalitet, tilbehør til træarbejde og et bredt sortiment af OEM-reservedele. Vi er forpligtet til at overgå forventningerne og samtidig bringe de bedste innovationer, teknologier og produktudvikling til branchen.

Ingen tilgængelige enheder

EAN: 0843441104469

Kategorier Værktøj og boligforbedring, Værktøj & Håndværktøj, Elektroværktøjsdele og tilbehør, Tilbehør til støvsugere & støvopsamlere, Dele til støvsugere og støvopsamlere,

MULTI-BRUG: Dette tilbehørssæt til støvopsamler indeholder komponenter, der er egnede til at understøtte op til fem støvopsamlingsmaskiner. KOMPATIBEL: Fungerer med de fleste butiksstøvsugere, centrale hjemmestøvsugere og/eller centraliserede støvudsugningssystemer. SYNLIGHED: Førsteklasses klare plastikrør giver dig mulighed for at rengøre med klarhed, spotte og fjerne blokeringer (savsmuldsopsamling, spåner osv.) hurtigt på ethvert trin i dit netværk. FUNKTION: Giver dig alt hvad du behøver for at udvide og opgradere dine eksisterende støvopsamlersystemer til træbearbejdning. INKLUDERER: (1) Reduktion af støvopsamling (8) 3 fods opsamlingsrør (5) sprængningsporte (4) Y-fittings, (3) 45 graders albuer (2) 90 graders albuer (22) rørkoblinger (10) klemmer og yderligere montering hardware.

Batteries Included?	‎No
Batteries Required?	‎No
Country of Origin	‎Taiwan
Customer Reviews	4.4 4.4 out of 5 stars 293 ratings 4.4 out of 5 stars
Included Components	‎Dust Collection Fittings Network
Item model number	‎70259
Item Package Quantity	‎1
Item Weight	‎14.82 pounds
Manufacturer	‎POWERTEC
Part Number	‎70259
Pattern	‎Fittings Network
Power Source	‎Hand Powered
Product Dimensions	‎37 x 11 x 10 inches
Size	‎2"
Style	‎Dust Collection Fittings Network

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med^*

Din vurdering

Scritto da: David Roberts

Parts fit loose

This came with the parts that I needed to set up my wood shop. The only downside is that some of the parts fit to loose. You can glue it together but then you can't make changes. So for now I have just secured the loose fittings with some tape until I am sure I like the way I set it up. 21/2 inch shop vac fittings fit great

Scritto da: Boxermamaldjbm

Could use some improvements

I purchased this kit to run dust collection through my basement woodshop. It's a great value with all of the pieces included with a few caveats. As many others have pointed out, the elbow pieces are worthless. As soon as I saw them, I knew I wouldn't be using them, which meant buying additional 45s. My other issue was with the Y pieces, they don't connect tightly at all and fall right back out, which meant they all had to be taped which I wasn't thrilled with, but what else can you do? The tubes themself lock very tightly into the connecting pieces, it's just anything involving those Y's. The Y's and the elbows could be greatly improved.

Scritto da: donba27

works fine but a little difficult to work with.

Just completed an installation hooking up a Ridgid Table saw, Ridgid Sliding Miter Saw, Wen Planer, Bosch Router Table, and Ryobi Sander to a Jet 1 ½ HP Vortex Dust Collector. I agree with one of the other reviewers that this is a poorly designed system in that you need a connector at every junction rather than having fitting like plumbing PVC where the pipes go into the fittings but this is the same with every other system I looked at. After a lot of aggravation, the system is completed and working fine. Some of the problems I found: 1. The couplings are VERY tight and hard to connect the fittings to the pipe especially the blast gates 2. The illustration shows that the first fitting that connects to the dust collector is a 90 elbow . DO NOT USE THE 2 90 ELBOWS THAT ARE INCLUDED IN THE KIT. It also shows that the Y Connector for each machine is lower than the main pipe. I followed the illustration and it worked fine when I was using a tool that created mainly saw dust but the first time I used the Planer, the larger shavings got clogged up at the 90 and the shavings that backed up dropped down into the Y connectors in the other hook ups between the planer and the 90 degree fitting. I had to take the 90 off and replace it with 2 45’s and Turned the Y fitting pointing up to prevent clogging and it seems to works fine. I don’t know why they even included 2 90’s because they are useless because the inside demention of the 90 gets smaller at the bend where the 2 45;s stays the same. 3. I bought the Powertec Anti Static Flexible PVC Dust Collection Hose to connect to each tool . It was considerably more expensive than the standard hose are more difficult to connect to the fittings and the machine. If I had to do it again I would just buy the standard hose which works just fine. Conclusion: This is the cheapest way to get the system up. Most of the other kits from other vendors may appear to be cheaper, but they don’t include the pipe. Each 3’ piece of clear pipe cost around $10.00 so the pipe included in this set is worth $80 alone. Extra blast gates and Y connectors are around $8 each so it’s simple …Do the math. Im happy with my setup and would recommend this for small shops.

Scritto da: Rick B

Avoid the 90-degree elbows

As several others have noted, the 90-degree elbows are poorly designed with a massive amount of solid plastic inside the bend. This creates a choke point that is only 1-1/2", pretty much ruining the airflow at that point -- might as well be using 1-1/2" pipe and fittings throughout if you use these. With a little effort the plastic CAN be ground out with a spindle sander or rotary tool outfitted with a sanding drum, but they should have been properly made to begin with. That said, the rest of the kit is very good, and a true bargain if you were to price and buy all the included components individually. Even deleting the two 90-degree bends from the package, it's still a workable and useful addition to a dust collection system for connection directly to machines with 2-1/2" ports.

Scritto da: gj

Easy to install

Works as expected.

Scritto da: Old Jer

Very well thought out product

Someone actually thought this out. It really comes with everything that you need for dust collection in a small wood shop except for flex hose that was $34 for a 20 ft length. Nice internally smooth fittings and clear pipe to see clogs. Simple, effective gates to control suction. I thought this might be junk when I ordered it, but it isn't. I ran it above my 5 machines with flex drops to each and it was stupidly simple to do. I have a 3hp dust collector but a good shop vac might be enough if emptied often enough. Essentially a couple dollars for each part, but everything works together. Given how most kits are junk, this isn't.

Scritto da: trippinjohn

Would be a great kit if it came with gates that were not useless.

The plastic gates that come with this are not worth installing, the grooves that the flat piece are supposed to slide through fill up with sawdust immediately, then they won't close fully which gives you a vacuum loss at every gate. You have to take apart the connections, remove the gate, and work furiously with a coat hanger or similar to get most of the saw dust out, then reassemble and you'll be good for a week. Way too much trouble. This company makes much better gates out of metal that have an anti-clogging feature that works, I don't know why they insist on using these plastic ones. I had to buy a set of the metal ones for an extra $53 to use my system, but even with that, it's a good value. All of the other stuff they give you is pretty good, and there's a lot of it! One tip on making connections: they tend to loosen up, but I found that putting one or two layers of painters' masking tape around the male ends before joining made the joints a lot more stable.

Scritto da: Michael

Best bang for your buck!

Absolutely as described. Easy to install. Much cheaper than piecemeal together a system. Made all the difference in my shop. Thank you for this excellent product!

Scritto da: Guillaume thibault

Aurais du acheter ca avant

J'ai branche ca sur un shop-vac 13 amp et ma longueur de ligne droite fait environ 20 pieds ! Je suis tres content de ce kit de tutau et aurais du acheter ca avant wow. J'ai pas de planeur par exemple.

Scritto da: Kathleen Yatkowsky

Just perfect

We purchased this system to use for our daycare busy wall. Kids attach the tubes to a shop vac and blow soft balls through the system

Scritto da: Denis Tremblay

C'est ok

Ramassage de poussière de bois