0
0

Total:kr 0.00

Se vognCheckout
LoginRegister
0

Total:kr 0.00

Se vognCheckout
LoginRegister

PacTool SS701 Snappersaks - Pladesaks - Pladeskæreboretilbehør - Skåret op til 18-gauge galvaniseret stål, aluminium og kobber - Pladeværktøj - Snedkerværktøj og tilbehør

Brand:PacTool

3.4/5

kr
756.44

PacTool SS701 Snapper Shear fastgøres til enhver 18-volt eller højere batteridrevet boremotor, så du kan skære 18-gauge galvaniseret stål, aluminium og kobber. Det er renere, hurtigere og minimerer metalspåner. Det ergonomiske universelle roterende skærhoved giver dig mulighed for nemt at skære enhver form, sparer timer, tilføjer bekvemmelighed og hjælper med at eliminere overskydende rod på enhver arbejdsplads. Afmonter og udskift nedslidte hærdede stålklinger med en ny udskiftningsklinge for at holde arbejdet i gang.

Beløb
Tilføj til kurvKøb nu

EAN: 0645646701005

Kategorier Værktøj og boligforbedring, Værktøj & Håndværktøj, Elektroværktøj, Sakse og nibblere, Sakse,

PACTOOL: Vi er kendt for vores konstruktions-, renoverings- og ombygningsprodukter og er specialiseret i avanceret udvendigt værktøj. Vores brede produktlinje hjælper fagfolk og gør-det-selv-ere med at bruge de rigtige værktøjer, hvilket øger produktiviteten, for at få arbejdet gjort. GARANTERET YDELSE: Du kan stole på, at PacTool-produkter giver enestående ydeevne og pålidelighed. Denne snappersaks er understøttet af PacTools et-års garanti mod fabrikationsfejl, pasform og finish. UDSKIFTELIGE KLINGE: Afmonter og udskift nedslidte hærdede stålblade med nye udskiftninger for at holde arbejdet i gang. Vores udskiftningsblade sælges separat. KRAFTIGHEDER GENNEM METAL: Skærer galvaniseret stål, aluminium, kobber op til 18 gauge og rustfrit stål op til 20 gauge. PacTool SS701 skæreudstyr skærer gennem ståltråd, mesh, vinyl, aluminium, sidespor, inddækning, metaltagbeklædning og trimspole. PROFESSIONEL KVALITET: Denne innovative saks fungerer med enhver 18-volt eller højere akku boremaskine og giver dig mulighed for nemt at navigere, mens du skærer. PacTool metal skæreværktøj er bygget til en standard, som efterspørges af kommercielle entreprenører.. ERGONOMISK FORDEL: Det universelle skærehoveds evne til at rotere 360° giver en brugervenlig oplevelse sammenlignet med traditionelle sakse. Brug snappersaksen til at skære lige, retvinklede, kurvede snit og skære cirkler ned til 3 tommer i diameter. ARBEJDE SMARTERE: Designet af denne elektriske boresaks minimerer metalspåner, mens den er i brug, hvilket giver fagfolk og gør-det-selv'ere mulighed for at skære og installere med lethed, hvilket øger effektiviteten og holder arbejdspladsen sikker.
Batteries Required? ‎No
Country of Origin ‎China
Customer Reviews 4.3 4.3 out of 5 stars 42 ratings 4.3 out of 5 stars
Included Components ‎
Item model number ‎SS701
Item Package Quantity ‎1
Item Weight ‎1.63 pounds
Manufacturer ‎PacTool
Part Number ‎SS701
Power Source ‎Battery Powered
Product Dimensions ‎2.5 x 7.13 x 2.65 inches
Style ‎Snapper Shear

3.4

8 Review
5 Star
55
4 Star
29
3 Star
12
2 Star
0
1 Star
4

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med*

Scritto da: OT
CUT NOT Straight
Its a good roduct and shear just fine. BUT HARD TO KEEP A STRAIGHT CUT!!!
Scritto da: Russell Martin
Heavy duty
The media could not be loaded.
Scritto da: Rico B.
Tool Requires Two Hands to Operate.
This tool is ideal for cutting pieces off a large metal sheet. The tool cuts through many different sheet metal gauges almost effortlessly and is a terrific addition to my toolbox. The cutters have a lot of cutting power and are sharp enough to leave a clean cut in the wake of the tool. The operation was slightly clumsy when the sheet metal would not hold still. You need to use a vice or cut a large enough piece of sheet metal that the part will not move. This tool is best operated with a helper because you need two hands to use the tool properly.
Scritto da: Kari31
Works pretty well
This works really well for what it is intended for and is easy to learn how to use.
Scritto da: frank farrar
General purpose. Not always better than old school.
I did like the cutting action with felt paper, vinyl siding trim, light rolled roofing, and expanded metal stucco backing when making long straight cuts in well secured sheets. Useful for materials that can be easily trimmed of that extra 1/4" of rough-cut material using more precise methods, either hand or cordless battery powered. For metal cutting this can work on a small project scale, but does not replace hole cutters, cordless jigsaws, or good quality hand shears. The advantage of fewer metal fragments is overstated, unless there is to be no cleanup trimming following the initial more or less rough cut. Yes, a jigsaw might be slower, but with a vacuum attachment there need not be much to clean up. With better control a single cut and a little grinder finishing, the job gets done without having to stop and deal with those nasty metal slivers, which are more or less unavoidable when any careful trimming is required. As always, it comes down to the frequency of the various useful procedures that can actually work. In my admittedly limited experience, a decent cordless jigsaw using top quality blades is the closest thing to a universal metal cutting tool. Slow, but precise. Not necessarily messy. Best of all, it doesn't generate a lot of metal heating issues, which is a great advantage of shears in general, by the way. If I had fifty bucks to spend on an improvement, I'd replace my worn-out jigsaw blades. If I were doing more occasional work in softer sheet materials, I'd definitely be happy with these low-cost cordless shears as a useful tool, where saw action can quickly get bogged down the moment the saw blade gets too warm to run ahead of the melting plastic or tar-infused component materials. In this case, the tool might fit the job well enough to be worth the cost for what it can do fairly well.
Scritto da: A.S.
Easy to get the hang of
These shears are a lot more convenient for me than using hand shears. You can cut metals up to about 18 gauge pretty easy. It cuts pretty strait as long as you keep the chuck tight. To make this tool work you have to have the material you are cutting very well secured so it doesn't move, since you have to keep both your hands on this shears as you use them.
Scritto da: Leo M.
It works as intended
Used the other day. Little awkward to use but it easily cut threw metal of an air conditioner cover. Wish the opening on the cutting blade was a little bigger but it worked fine on what I was doing
Scritto da: Thomas Reed
Effective Shears For Metal And Other Material
The Pac Tool shears were ordered for use in my workshop & around my house. This is an effective metal cutting tool for a DIY workshop and perhaps those who are professionals. In testing, what I found was that this tools is heavy when added to an 18V (or more) cordless drill and obviously must be used with 2 hands. The tool cut through the sheet metal easily with very little issue on straight cuts. Curved cuts were a little problematic. One thing that I would suggest in using this tool is some gloves and eye wear. I am particular to wearing protective eye wear when using cutting tools since small slivers are a possibility in these types of tools. Overall, I found this tool to be effective when cutting sheet metal and other metal up to 18 gauge. In addition, though I did not test this, it may be effective in cutting non-metalic material that is not extremely thick.

Relaterede produkter

hot
Malco TSHD Turboshear Heavy Duty Metal skærebeslagsaks, sort
3.7/5

kr 1259.22

Malco TSHD Turboshear Heavy Duty Metal skærebeslagsaks, sort
3.7/5

kr 1259.22

hot
Malco TSS1 Asfalt Helvedesild Turbosaks
3.2/5

kr 2863.52

Malco TSS1 Asfalt Helvedesild Turbosaks
3.2/5

kr 2863.52

hot
Shop Fox M1041 pladesaks, 12-tommer
3.5/5

kr 5416.14

Shop Fox M1041 pladesaks, 12-tommer
3.5/5

kr 5416.14

hot
Malco TSF1 Turboshear Fiber Cement Siding Shear
3/5

kr 2430.20

Malco TSF1 Turboshear Fiber Cement Siding Shear
3/5

kr 2430.20

hot
PacTool SS704 Snapper Shear Siding Pro - Sideskæresaks - Akku-boretilbehør - Professionelt elværktøj Boretilbehørsskærer
3.4/5

kr 876.93

PacTool SS704 Snapper Shear Siding Pro - Sideskæresaks - Akku-boretilbehør - Professionelt elværktøj Boretilbehørsskærer
3.4/5

kr 876.93

hot
DEWALT 20V MAX metalsakssæt, drejehoved, 18GA (DCS491M2)
2.8/5

kr 4166.44

DEWALT 20V MAX metalsakssæt, drejehoved, 18GA (DCS491M2)
2.8/5

kr 4166.44

hot
BOSCH 2608635243 16 Gauge Universal skæreblad
3/5

kr 589.83

BOSCH 2608635243 16 Gauge Universal skæreblad
3/5

kr 589.83

hot
Malco TSHD1 Automotive Heavy Duty 18 Gauge Turbo skæreboreudstyr
3.7/5

kr 1658.54

Malco TSHD1 Automotive Heavy Duty 18 Gauge Turbo skæreboreudstyr
3.7/5

kr 1658.54

Oplev vores internationale netværk

Vi sender til 28 lande, over 200.000 produkter. Hold dig opdateret, tilmeld dig nyhedsbrevet.

Array

Total:kr 0.00

Se vognCheckout

Kategorier

Alle kategorier
Menu Kategorier Nær ved Vogn

Menu