Diamantbearbejdningsteknologi (DMT) D6EF Dia-Sharp 2-sidet diamantslibesten bænkplan, 6 tommer, fin/ekstra fin

Name: Diamantbearbejdningsteknologi (DMT) D6EF Dia-Sharp 2-sidet diamantslibesten bænkplan, 6 tommer, fin/ekstra fin
Brand: DMT
SKU: 753956891535
Price: 744.61 DKK
Availability: InStock

Brand:DMT

3.3/5

kr
744.61

PRODUKTBESKRIVELSE Vælg DMTs 6-tommer dobbeltsidede Dia-Sharp diamantslibebænksten. Med 2 kornmuligheder er den ideel til brug med knive, klinger og fint værktøj. Fin diamant (25 mikron / 600 mesh) skaber knivskarpe kanter, mens Extra-Fine (9 mikron / 1200 mesh) polerer og forfiner efter slibning med en grovere diamant. Holdbar konstruktion vil give mange års ensartet ydeevne og pålidelig service. For korrekt værktøjsvedligeholdelse stoler fagfolk på den overlegne kvalitet og alsidighed af USA-fremstillede DMT-produkter. FRA PRODUCENTEN Til benkestensanvendelser, hvor alsidighed er vigtig, men opbevaring er begrænset, skal du vælge DMTs 6 Dobbeltsidede Dia-Sharp kontinuerlige diamantslibebænksten. To kornmuligheder i ét sten. Til knive, klinger og fint værktøj. Fin diamant (25 mikron / 600 mesh) for en knivskarp kant. Ekstra fin (9 mikron / 1200 mesh) til at polere og forfine en barberkniv efter slibning med en grovere diamant. Størrelse: 6 x 2 x 1/4 Diamantkvalitet tydeligt markeret på hver side af stenen. Slibning med diamanter er hurtigt og nemt. Ingen rodede olier nødvendige - slib tør eller med vand. Holdbar konstruktion vil give mange års ensartet ydeevne og pålidelig service For korrekt værktøjsvedligeholdelse stoler træarbejdere, kokke og andre fagfolk på den overlegne kvalitet og alsidighed af DMT-produkter. Lavet i USA.

Beløb

Tilføj til kurv Køb nu

EAN: 753956891535

Kategorier Værktøj og boligforbedring, Værktøj & Håndværktøj, Håndværktøj, Slibesten,

Holdbar konstruktion vil give mange års ensartet ydeevne og pålidelig service. Ingen olie er nødvendig - slib tør eller med vand. Diamantkorn tydeligt markeret på siden af stenen. Fin diamant på den ene side for en knivskarp kant og ekstra fin diamant på bagsiden for at polere og forfine. Dobbeltsidet knivspidser med monokrystallinsk diamantoverflade. Fremstillet i USA: Foretrukken af fagfolk for deres overlegne kvalitet og alsidighed, vores holdbare diamantslibesten er bygget til at give mange års ensartet ydeevne og pålidelig service. Skærp hurtigere: Mikroniseret monokrystallinsk diamantoverflade skærper kanterne hurtigere end konventionelle slibesten; Der er heller ikke behov for rodede olier - slib lappladen tør eller med vand. Alsidig: Konstrueret til at give banebrydende ydeevne, denne 6-tommers diamantstensliber er ideel til at slibe, polere og raffinere knive, klinger og fint værktøj. Fin og ekstra fin: Fin (25 mikron / 600 mesh) finpudser enhver klinge eller mejsel til en knivskarp kant; Extra-Fine (9 mikron / 1200 mesh) polerer og forfiner efter slibning med en grovere diamant. Diamond Wet Stone Sharpener: Tilbyder 2-trins slibning og et kompakt design, denne lette diamantsten er fantastisk til hjemmet, autocamperen, værktøjskassen, haveskuret og mere.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	DMT
Brand	DMT (Diamond Machining Technology)
Color	White
Color	‎White
Country of Origin	‎USA
Customer Reviews	4.3 4.3 out of 5 stars 424 ratings 4.3 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Grit Description	‎Extra Fine,Fine Grit
Grit Type	Extra Fine,Fine Grit
Included Components	‎Dia-Sharp Bench Stone
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Item model number	‎D6EF
Item Package Quantity	‎1
Item Weight	12.8 Ounces
Item Weight	‎12.8 ounces
Manufacturer	‎DMT
Material	Synthetic
Material	‎Synthetic
Measurement System	‎Metric
Number Of Pieces	‎1
Part Number	‎D6EF
Product Dimensions	11"L x 6"W x 4.25"H
Product Dimensions	‎11 x 6 x 4.25 inches
Size	‎One Size
Special Features	‎Manual
Style	‎Fine/Extra Fine
Warranty Description	‎Manufacturer Warranty

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med^*

Din vurdering

Scritto da: Bh

Good diamond stone.

I had to send two of these back to Amazon because the stones where of poor quality. They where very roughly machined, so the surface of the metal underneath the layer of diamond was not even close to smooth, I did not like the idea of my blade running into nicks and deep gouge marks in the stone. Then the second stone I got was much smoother, but the layer of diamond thinned out to almost nothing on one corner of the stone, sent that back and finally got a good product. Once I received the good stone, free from defects, I will say it is a great stone. DMT diamond stones really are great, I have used other brand diamond stones, and they don't compare to this one. The DMT stones cut fast, yet leave a nice fine finish for being as aggressive as the are. Use light pressure with these stones, they cut fast and do not require much pressure. These stone do have a break in period, they will feel a bit gritty and rough at first, but mine did break in nicely and feel much smoother when sharpening. Also as they break in they will become slightly less aggressive, but they still cut pretty fast. I bought this stone because it was double sided and seemed like a good value. The fine side can give you a really nice sharp edge without even using the extra-fine side. The extra-fine will further refine the edge, but honestly is not needed to create a razor sharp edge. I already had a DMT course, so I went with this stone to complete the grit range. I would say if you don't already have a coarse stone, buy the double sided coarse/fine and have one stone that can reprofile and repair an edge using the coarse side, then have the fine side to put on a keen edge.

Scritto da: Nadia Sidorov

The only stone you’ll ever need!

Quality - [8/10] (ends have visible marks from when it was cut with a bandsaw) Feel - [10/10] This stone just feels like a quality product. Also, it is very responsive and feels great when sharpening Functionality - [10/10] The “fine” side of this stone is rated at 25 micron (~800 grit) which is great because it can remove a good amount of material fairly quickly while providing a very workable edge. I sharpened my Para 3 in S110V steel (known for being extremely difficult to sharpen) in about 10 minutes. The knife was dull (hardly shaving any hair) and after using the “fine” side and stropping on 5micron and 2.5micron diamond paste, the edge would easily shave. After that i tried out the “extra-fine” side; which worked amazingly. The “extra-fine” side left the knife hair-popping sharp straight off of the stone! (I used a push-pull method to form a burr on both sides then forward strokes alternating sides each stroke to remove the burr). After the stone i brought the knife to my 2.5 and 0.5 micron diamond paste strops and the edge was mind-blowing. It will shave hair without any pressure (just the weight of the knife) and even cut a single piece of hair in half while it is hanging. In conclusion, this stone is excellent. It works for establishing bevels as well as taking them to shaving sharp. This stone is truly the only stone you’ll ever need. And if it’ll cut s110v in ~15 minutes... It’ll cut any steel for any knife, axe, chisel, plane, anything. Thank you for reading, hopefully this was helpful.

Scritto da: Yup

Needed something to maintain my chef's knives

Was watching a You Tube video about keeping the tools of the trade sharp and asked what grit they were using, theirs was labeled fine and one sided with rubber feet to keep it from sliding. This is twice as good, fine one side and extra fine on the flip side, I just got some dollar store round 'shelf liner' disks and does not move about. As noted by others and also on the package it requires a bit of break-in so before going after my good cutlery I set it on my counter, gave it a spray of water and sharpened a lockback knife I had found in the cupboard when I bought my house 2 years ago, it had been abused and looked like the previous owner had 'sharpened' it on a cinder block! It was BAD! Five min later honing it on the fine side it was slicing about half the blade length through a sheet of paper, not bad considering I have really never gotten a good edge on anything using a oilstone - arkansas stone combo. So another min on the fine side and flip to the extra fine side that beat up Shrade "Uncle Henry" was pulling a slice the length of the blade plus some. (It also broke in the block smoothing off any high bits) Touched up my 10" chef knife and it is as sharp as it was 2 years ago when I got it. Takes a bit of practice and a steady hand to maintain the correct angle but this is the best sharpening "Stone" I have ever had!

Scritto da: Camden

Fair quality, good results.

I've been sharpening knives of my own for about 20 years now and wanted to give DMT a shot. I'm satisfied with the double-sided "stone" overall. The stock metal that holds the braze seems like it could be more consistently flat. Or the braze of diamonds could be applied unevenly, creating a not so flat surface. Some small areas of the stone are completely unbrazed, just showing bare metal. And even after a few hours of use, there are still tiny little clusters of diamonds that stick up just enough to barely nick the fine edge the extra-fine side can make. Therefore, this product is not for perfectionists. I will say of all the different types of steel I've sharpened with this stone, none of them were too hard to be cleaned up and taken to a fine edge. Razor sharp results can be obtained using the extra-fine side, save the occasional nick here and there. To get "stupid" sharp edges, a few passes on a ceramic or glass rod can make most knives too sharp to hand over to your wife or buddy. I recommend this stone to the experienced woodworker or ninja chef who wants a keen, but slightly imperfect edge on their tools.

Scritto da: maxx

Not completely flat. Overpriced in regards to production quality.

I would say my $20 S SATC Diamond plate is much better for half the price. It's lasted twice as long, it's flatter, and bigger.

Scritto da: David Anderson

Out standing

These diamond sharpening stones are top quality and well worth the money. Please note that you must break in your stone this can take a few weeks they get better and better with use. I’ve owned mine for a few months now and it’s now perfect regards Dave

Scritto da: Ramesh G.

Four Stars

Good quality product on first sight . Will put to use from next month only

Scritto da: Leo

Excellent sharpening stone

Excellent sharpening stone. Because the abrasive is diamond, it can cut vanadium carbides that are present in common "super" steels such as CPM 3V, CPM S30V, and CPM S35VN. Many people say sharpening those steels takes a while, and the edge doesn't last very long, but that's because they are sharpening with abrasives that are softer (has a lower Rockwell hardness) than the vanadium carbides, and because of this, the vanadium carbides do not get sharpened, only the steel matrix around it does, so the carbides fall out. The whole purpose of vanadium carbides is that they are very hard, while means that they will hold an edge for a very long time IF SHARPENED. If you want to sharpen a steel that has vanadium carbides, make sure you get a diamond stone! I also got the plastic base sold by DMT that is compatible with this (and any other 6" stone) and they work great together!

Scritto da: Tino

Just a bit disappointed.

Firstly, I've been using DMT products for a very long time. I originally bought their products at Langevin & Forest when started cabinetmaking. Since then I've been using the cards and the mini-hone kit for a significant number of small tool sharpening, and the dual-sided fine/x-fine for a ridiculous number of sharpenings, and it still works. I've sharpened dozens of tungsten-carbide cutting tools on it and saved one of my employers hundreds of dollars, maybe more than hundreds, with it. DMT has never let me down and has done so much for my hobbies, and I've recommended it to around a dozen buddies. Normally I remove lots of material with some of the many industrial rolls of sanding-belt sandpapers that had been thrown away at one of my works. This works very well for most all of my tools. However I was searching for a more portable solution to help me sharpen my friends' knives without toting a handful of concealed blades through the metros and buses to get home, and then do it again. I tried the Chef's Choice 130. It works very well for just about anything, especially very dull knives, but I can get a better edge on a knife in not much more time with the right equipment, and I can get shape a knife better, and get the criss-crossed tooth / cutting pattern that I find grips while cutting in both directions better and cuts tomato skins better. So I went with this for the very dull knives, and will still tote my fine/-x-fine along with it. I just got this one in the mail today, all giddy for a new toy.. and what I found was a lip on the coarse side. If it was the x-coarse side, meh, the coarse side would remove any damage after. But it is on the coarse side. I have already spent a few minutes grinding that lip down so it cannot do any damage or cause extra time on the fine/x-fine "stone." But for the cost of DMT products, I wasn't expecting a lip. I don't care unduly, but for the cost of DMT products I expect full coverage of a side, and no darn lip! The coarse side has a section the width of the lip in the picture that goes all the way around just that one side, and that section has little to no diamond on it. This feels like a budget cut! I doubt it'll add more than a few minutes work to my entire life due to the small lack of diamonds, but still.

Scritto da: James D

Sharp

Works well for my chisels, was happy with wet stones but they cave to quick, this has solved that problem, very happy.