CURT 56334 Køretøjsside tilpasset 4-benet trailerledningsnet, passer til Select Dodge Nitro, Jeep Liberty , Sort

Brand:CURT

3.7/5

kr
872.30

Hvis dit køretøj ikke er udstyret med ledninger til at trække en trailer, er CURT brugerdefinerede ledninger den ideelle løsning. Et brugerdefineret ledningsnet - også kaldet et T-stik - er en enkel, plug-and-play elektrisk enhed, der tilsluttes dit bilelektriske system og giver en standard, universel anhængerledningsforbindelse. Dette gøres ved hjælp af to eller flere køretøjsspecifikke, OEM-kompatible stik til at tilslutte til baglygtesamlingen, hvilket eliminerer behovet for skæring, splejsning og lodning under installationen. Brugerdefinerede ledningsnet er gjort køretøjsspecifikke, og selvom de ikke er tilgængelige til alle køretøjer, tilbyder de en af ​​de hurtigste, nemmeste og sikreste måder at forbinde et køretøj til bugsering. Denne særlige plug-in-sele giver en 4-vejs flad stikdåse og er designet til at være et brugerdefineret ledningsnet, der passer til visse år af Dodge Nitro og Jeep Liberty (for at verificere dit køretøjs kompatibilitet, se ansøgningsoplysninger). Den leveres med alle nødvendige ledningskomponenter for at etablere en pålidelig anhængerledningsforbindelse, samt et støvdæksel for at holde stikket rent, når det ikke er i brug. Du har et billede i tankerne af din næste destination -- måske er det båden, der lander på dit foretrukne fiskested, måske er det en campingplads, der har udsigt over et af naturens mesterværker, eller måske er det den næste store arbejdsplads. Men at gøre dette billede til en realitet kræver mere end blot at dagdrømme. Det kræver en solid forbindelse og den rigtige mængde strøm. CURT brugerdefinerede ledninger er lavet med noget af den mest sofistikerede teknologi i branchen og er designet til at installere med lethed, hvilket giver dig en langvarig elektrisk forbindelse til dit anhængertræk.

Ingen tilgængelige enheder
STØVDÆKKE. For at fremme langvarig brug og vejrbestandighed leveres denne 4-polede ledningsnet til trailerbelysning med et gummistøvdæksel. Den passer nemt på det 4-vejs flade stik, når den ikke er i brug, og beskytter den mod udendørs elementer. PÅLIDELIG KRAFT. Dette 4-vejs anhængerledningsnet er bygget med overflademonteringsteknologi. Denne type kredsløb genererer mindre varme, optimal lysintensitet og holdbar ydeevne. KØRETØJSSPECIFIK. Dette eftermarked, køretøj-trailer ledningsnet er designet til udvalgte år af Dodge Nitro og Jeep Liberty. STANDARD KONTAKT. Denne plug-in 4-flade trailerledning kan bruges til at forbinde trailerbaglygter, bremsesignallys og blinklys. 4-vejs trailerlysledninger er populært på en række forskellige trailere, hvilket tilføjer alsidige bugseringsmuligheder til dit køretøj. LET AT INSTALLERE. Ingen skæring! Ingen splejsning! Dette anhængerledningssæt tilsluttes eksisterende fabriksledninger på dit køretøj og udstyrer det med et standard, bageste 4-bens anhængerledningsstik til at tilslutte og trække en anhænger.
Brand CURT
Brand ‎CURT
Country of Origin ‎Philippines
Customer Reviews 4.7 4.7 out of 5 stars 281 ratings 4.7 out of 5 stars
Exterior ‎Painted
Item Dimensions LxWxH 9 x 6 x 3 inches
Item model number ‎56334
Item Weight ‎1.81 pounds
Manufacturer ‎CURT
Manufacturer Part Number ‎56334
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎56334
Product Dimensions ‎9 x 6 x 3 inches

3.7

11 Review
5 Star
80
4 Star
14
3 Star
3
2 Star
1
1 Star
2

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med*

Scritto da: Christian Triplett
Quailty is great
I was a little hesitant about buying one of these because previous module installs didn’t work for me. However I bought this on a whim for my camper and it is has worked since day 1. It took a bit to install it cleanly. But I have had no issues with my trailer wiring since. It caught me off guard when I saw that the trailer turn signal will flash alternate to the car when the brakes are applied at the same time as the turn signal. But I’ve been running it for a few months without issue!
Scritto da: Marcos Santiago
Perfect fit
Installed in less then 30mins.
Scritto da: P K
Works as it should in 2009 Jeep Liberty, a bit of a challange to install (vehicle issues)
Trailer wiring harness was overall a good product for a good price. Installation was a bit of a challenge in several areas, but this is more of a Jeep/vehicle issue than the wiring harness fault. Not much room in the rear tail light areas for the 2 extra connectors. The instructions call for mounting the module under/outside the vehicle, but I mounted the electronic module inside the vehicle (in the jack compartment), and had to cut the factory rubber plugs where the vehicle wires go through the body to the tail lights in order to make these connections. Also, I had to remove several inside plastic body panels in order to fish the main power wire from the engine compartment to the rear of the vehicle. (HINT: Rubber plug in firewall where clutch rod would be if a manual tranny. No rod (easy access) if auto tranny.) One concern: I measured 0.3 volts from each of the 3 "Light" wires to ground even when the vehicle is not running. I'm sure this is something with the electronic switching of the module. A disconnect switch could be installed in the power wire when not using to eliminate this issue.
Scritto da: Gary G.
A Must-have accessory for DYI installers.
This harness was easy to install on my 2011 Liberty. There was plenty of room in the tail light recess for the extra plugs and wiring. The routing of the power line to the battery was a bit of a challenge to avoid the moving parts of the rear suspension and the exhaust system but it can be done with care. My only minor complaint is with the module. Even though I found a flat painted surface and cleaned it extremely well, the double sided mounting tape became loose within hours. I was able to secure the module using the mounting tab on the one end, but additional mounting tab(s) would be preferable.
Scritto da: Edward P.
Fit meant
Great price worked as it should and fast delivery
Scritto da: Lionel A Richard
Instructions clear but you do need some experience in automotive electrical wiring
Easy to install
Scritto da: Christa L. Barnes
Easy to install
Easy installation, clear directions
Scritto da: Jason J McKoy
Plug and play almost.
The product is great it sure beats the old days of splicing in the wires take your time and dont usse the double sided sticky tape to hold up the controller tou might get a 1/4 mile before it falls off self tap it in!
Scritto da: David P.
Easy to install
Product was easy to install. Trailer lights now work perfectly.
Scritto da: Cityslicker
Perfect wiring harness for my jeep
Delivery was on time. Plus easy installation and worked the first time.
Scritto da: Carrie
Wiring Harness Drained Battery
I hooked this up in August to my 2008 Jeep Liberty, which I only use to pull a trailer in the summer. After the Jeep sat for a couple of weeks at the end of the season, it wouldn't start. The Curt custom wiring harness 56334 is drawing constant power, and drained my battery (which was brand new in June). When I remove the fuse from the wire that goes to the unit, the battery is fine as it doesn't draw power, and the Jeep starts every time. I believe I have a faulty unit and would like it to be replaced as it should not draw power when not in use. I can't find any contact information for customer service. I am hoping that Curt Manufacturing will reach out to me to make this right.

Relaterede produkter

Oplev vores internationale netværk

Vi sender til 28 lande, over 200.000 produkter. Hold dig opdateret, tilmeld dig nyhedsbrevet.

Array