CURT 19101 Camper Ophæng til 2 x 4-tommer RV kofanger, 2 tommer modtager, 3.500 lbs

Name: CURT 19101 Camper Ophæng til 2 x 4-tommer RV kofanger, 2 tommer modtager, 3.500 lbs
Brand: CURT
SKU: 0612314009947
Price: 1255.48 DKK
Availability: InStock

Brand:CURT

3.4/5

kr
1255.48

Et CURT RV-træk er et anhængertræk, der er designet til at monteres på bagsiden af et fritidskøretøj for at tilføje ekstra lastrum. Disse træk er fremstillet ved hjælp af CURTs kvalitetsprocesser med robotsvejsning, grundig rengøring og præcis finish. Vores RV kofangertræk er belagt med en flydende A-coat efterfulgt af en blank sort pulverlakering for lasermodstand mod slid og korrosion, og de tilbyder en 2 x 2 modtagerrøråbning. Dette særlige kofangertræk har en samlet anhængervægtkapacitet på 3.500 lbs. og en tungevægtkapacitet på 350 lbs., hvilket gør den til et glimrende valg til at trække et cykelstativ, en lastholder, en bådtrailer eller en lille brugstrailer bag din RV. Den kan også bruges til at trække en anhænger til fritidskøretøjer, så du kan tage den ATV, vandscooter, jordcykel eller andet legetøj med på turen. Sørg for altid at kontrollere anhængerens bruttovægt og vægtklassificering af kofangeren før bugsering. CURT RV-træk er ikke blot endnu et tilbehør til din autocamper; de er et produkt af smart konstruktion og kvalitetskonstruktion for at hjælpe dig med at opnå den ultimative RV-oplevelse, hver gang du kører på vejen.

Beløb

Tilføj til kurv Køb nu

EAN: 0612314009947

Kategorier Køretøj, Eksteriørtilbehør, Towing Products & Winches, Hitches, Receivers,

LET AT INSTALLERE. Installation af denne autocamper anhængertræk er hurtig og nem. Den boltes sikkert på stort set enhver 2-tommer x 4-tommer RV-kofanger med den medfølgende grad-8-hardware og typisk kun nogle få værktøjer. RUST, AFSNIT, UV-resistent. Dette autocamper kofangertræk er beskyttet med en dobbeltlagsfinish af rustbestandig A-coat og meget holdbar sort pulverlak. Finisherne er co-hærdet for exceptionel modstandsdygtighed over for rust, skår og UV-stråler. FULDSTÆNDIG TESTET. Hvert CURT autocampertræk er testet på vores Detroit ingeniøranlæg i henhold til SAE J684 standarder for den største sikkerhed og pålidelighed under bugsering. ALSIGTIG DESIGN. Denne autocamper med anhængertræk udstyrer din autocamper med en standard 2-tommer x 2-tommer ophængsmodtager, hvilket giver mulighed for en bred vifte af bugseringsmuligheder. Den kan acceptere kuglebeslag, lastholder, cykelstativ, trækkrog og meget mere. PÅLIDELIG STYRKE. Dette RV anhængertræk er normeret til 3.500 lbs. total anhængervægt og 350 lbs. tungevægt (begrænset til den lavest vurderede bugserkomponent).

Brand	CURT
Brand	‎CURT
Country of Origin	‎USA
Customer Reviews	4.3 4.3 out of 5 stars 231 ratings 4.3 out of 5 stars
Exterior	‎GLOSS BLACK POWDER COAT
Finish Type	GLOSS BLACK POWDER COAT
Is Discontinued By Manufacturer	‎No
Item model number	‎19101
Item Weight	‎12.62 pounds
Manufacturer	‎Curt Manufacturing
Manufacturer Part Number	‎19101
Material	Carbon Steel
Model	‎RV Bumper Hitch
OEM Part Number	‎19101
Product Dimensions	‎11 x 9 x 6 inches
Vehicle Service Type	Marine-Personal-Craft, Off-Road-Motorcycles, ATV, Trailer

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din anmeldelse

Din e-mail vil ikke blive offentliggjort. Alle obligatoriske felter er markeret med^*

Din vurdering

Scritto da: Matt Rosario

Didn't fit my bumper, believe the part was defective

Did not fit my bumper. I believe it was defective (poor quality control). There were weld beads that ran to the inside of the mount that sat against the bumper that prevented the bolts to align with the holes. The product seemed sturdy and able to hold a good amount of weight, if only I could have used it. I sent the item back for a refund with zero issues.

Scritto da: Doug

Very Nice for Camper hitch

We bought this and attached it to the Y frame on the front of the camper. We use it to store our weight distribution hitch so that is does sit in the truck. We lock it in and it is out of the way.

Scritto da: Amazon Customer

Cut to Fit

This is an update to my original review. I originally returned the Curt camper hitch in the hope of finding something that fits better. Failed in that goal and rebought the item. Had to seriously modify the hitch to fit it on my aluminum camper trailer. (I only need it to store my truck's bed extender.) Using a angle grinder to cut the hitch down to fit was actually the easy part. Drilling new holes in the very thick steel was non-trivial. Think it will be fine.

Scritto da: Richard Lindley

Saved me big bucks!!!

If you are mechanically inclined this will work on a Highlander bumper. Drilled the aluminum bumper slipped this right in place trimmed the bumper cover been hauling trailers ever since. You don't need a converter switch installed under your dash either or a fuse in your fuse box. Your lights will go onto a line that will always have power as long as the switch is on. Find your signals and your break. That's it you will always have daytime running lights but saves you the time and money for the converter that will pulse your lights. This is because most vehicles don't have a separate signal light like the highlander. Most vehicles pulse the taillight for the signal already.

Scritto da: aric kane varner

Great Receiver for Trailer!

I took and cut this down and re-drilled the top holes to fit the 2"x3" rear cross rail at the back of my boat trailer. Added a pigtail to the back of the boat trailer to plug the ski trailer into for the lights. Now I can pull my jet ski behind my boat like a champ! I ran that boat/ski trailer combo all summer long at 80 mph! No problems whatsoever! Heavy duty construction! Nice black finish! Well built product! Very pleased!

Scritto da: josh warren

Fits a Boss plow crossmember on a 2015-2019 GM HD pickup!

After I had my plow installed I wasn't thrilled about losing my front receiver. I measured the plow crossmember and guessed that this would fit, and I guessed right.

Scritto da: RickieDean

Just what i needed

I installed this hitch on the back of my Toy Hauler Travel Trailer to carry our Bicycles,the Curtis hitch is very well maid, easy to install and allows me to use my hitch bike rack,Love it.

Scritto da: Poolplayer

Description is Misleading - 4"x2" bumper

I wanted to leave this information so others won't be as confused about this product as I was. I was very hesitant to order this as I was looking for a camper bumper hitch to be used for a bike rack. My camper bumper is 4" high by 2" deep. Most rv bumper hitches are for a 4"x4" bumper and this one (Curt 19101) on Amazon and most other web sites that sell this, specify it will fit a 2" square channel bumper. This description in wrong as it fits and is made for my 4"x2" bumper!!!!! Chalet Arrowhead Very solid product and as always, Amazon Prime shipping was fast, showed up next day!

Scritto da: ken

Quality

Great quality and easy to install.

Scritto da: Ryan K.

Great hitch

Bought for a bike rack on my 2x4 C channel bumper on my camper trailer. Very heavy duty hitch... Way more than I needed. Had to do some minor modification to my bumper for it to bolt on properly. For the price, it wasn't worth sending back and only cost a few bucks to do the modifications to make it fit. Great product.

Scritto da: Mike M

Great addition to our trailer for carrying accessories

Works great to add a bike rack to our pop up trailer

Scritto da: Dave Pringle

Worked for me, a cheap alternative

I bought this hitch for a 2014 Mitsubishi Mirage, not to use to pull anything but as a means of being able to mount a 'load extender' type of thing onto the hitch and thereby help carry kayaks and canoes. I'm sure it will also come in handy on trips to the lumber store etc. The problem everyone who will have done this knows, is that mounting a kayak or canoe to a roof rack requires a person to twist their back around in a way that can cause a problem, especially when you get to my age. With an extender, one can tip up the front of the canoe/kayak onto the bar and then slide it forward onto the vehicle. I have not as yet tried this but am looking forward to using this new system!

Scritto da: maryse

Very solid !

I found this piece to be excellent and well made. It didn't suit us for what we needed it for but I definately recommend it if you have the right size bumper.